Installing a GPS tracking device in your vehicle shouldn't be a sophisticated activity, however it is crucial to take security precautions, as such the installation ought to only be carried out by a certified Auto Electrician. Usually, it takes approximately 2 hours to set it up relying on the complexity of the vehicle’s wiring construction. GPS device installation (basic installation with no gas/temperature/door sensors related), pet gps alternative learn the next directions. Read extra on the Do’s & Dont’s of GPS device set up at the top of this document. Screwdriver set, Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before putting in the machine, you want to note down International Mobile Equipment Identity (IMEI) variety of the GPS tracking device and the SIM GSM number. Then insert the GPRS enabled SIM card to the device. You could as effectively obtain the car addition template to record car data. Then insert the GPRS enabled SIM card to the device.
(Image: https://media.istockphoto.com/id/1356769489/photo/apocalypse-and-nuclear-war.jpg?s=612x612&w=0&k=20&c=5NI__0jdBphYH_SPlD7jgFUpVm1tuT3r06T98IsugzU=)It's possible you'll as nicely download the vehicle addition template to document car info. IMEI is a singular quantity to establish GSM, WCDMA, and iDEN cell phones, satellite tv for pc telephones, in addition to some telematics devices that works as a unique identification code. This 15-digit quantity is usually printed either on the bottom of the GPS monitoring unit or the gadget case; you require IMEI to register the GPS tracking device on the fleet management software. Red wire (of GPS machine) to at least one finish and the power source of the vehicle to the other finish of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or itagpro locator wire with -ve power). Connect Yellow ignition sense wire to the vehicle’s ignition supply to help observe ignition ON/OFF occasions. Please consult the vehicle wiring diagram to find the ignition wire.
You may confirm the automobile ignition wire by measuring the vehicle’s operating voltage while the engine is running. Once recognized, iTagPro locator connect the ignition wire to the FUSE Box with a 3M Scotchlok so that it will snap into place and iTagPro locator can get it correctly seated. Please confer with the connection diagram under, for an in depth view of the wires & connectivities. One of the quickest and the very best place to mount a GPS tracking device or a GPS tracker is under the dashboard or an exterior location in a horizontal position with a transparent view of the sky. You might experiment with putting the tracking device at completely different places on the automobile to find out the most effective reception for the desired stage of concealment. If the gadget has exterior iTagPro locator GPS antenna then place the antenna beneath the dashboard or wherever handy utilizing double-sided sticky-tape to make sure it’s firmly fixed there. Once you’ve positioned the GPS tracker in the vehicle, you’re all set.
(Image: https://freepixels.com/wp-content/uploads/Nature/Landscape/030808a6765-field-haystack.jpg)Connect the wire socket and GPS/GSM antenna (of those with exterior iTagPro support antenna) to the GPS machine. As quickly because the machine is powered on, each inexperienced LEDs (GPS & communication) will flash on and off while looking for iTagPro website indicators. When full sign energy is achieved, each LEDs will repeatedly illuminate. To be able to validate functionality, iTagPro locator we need to ring the GSM cell variety of the SIM. If it rings or responds with a busy be aware, you'll be able to safely assume that the gadget is functioning properly. If there isn't a response, you might need to re-insert the SIM card and check the wiring once more. Please Log into the platform with your credentials to ensure the machine communicates with the server. Note: Be sure that the IMEI no’s & mobile no’s you updated in opposition to the automobiles are correct. To keep away from mishaps while installation, be sure that the vehicle ignition is turned off earlier than initiating wire connections. It is always advisable to disconnect the suitable jumpers /connections of vehicle’s power provide through the GPS machine installation; this is to keep away from quick circuits and wiring damages.
Be sure that the wires keep disconnected whereas mounting/dismounting the system. Secure all wiring with Scotchlok, cable connectors, and ItagPro electrical insulation tapes. Never enable any naked wiring to remain uncovered; connections should be least visible. Ensure further insulation if wires go through a visible/exterior area, in order to avoid quick circuit/wiring damages. GPS monitoring devices might be mounted in a zone of restricted entry, so none has direct access to the instrument. Keep connecting wires as discreetly as possible, making it much less seen and laborious to notice. For the security of personnel, gadget & car, keep away from connecting machine wires to the board computer systems (ECU) or iTagPro locator management items. Ensure that you just fasten wires to different wires/non-moving components and not to fasten close to heat emitting and shifting objects as friction/heat emission may trigger sparks leading to brief circuits. While connecting ignition wire confirm if it’s the actual ignition wire (power supply obtainable only when the ignition is on). Using a multimeter, iTagPro smart tracker verify power stream by turning on/off the engine.